The Welder / Fitter lays out, fits, and welds steel and aluminum components and weldments for defense products built to customer drawings and military specifications. This role works primarily out of position, with sustained vertical and overhead welding on parts too large or awkward to rotate into the flat or horizontal position. The Welder / Fitter is responsible for the full job from print to finished weld: reading the drawing, setting up the fit, holding tolerance, producing sound welds that pass visual and nondestructive inspection, and documenting the work.
ESSENTIAL DUTIES AND RESPONSIBILITIES
Fitting and Layout
- Read and interpret engineering drawings, weld symbols (AWS A2.4), and basic GD&T to determine fit-up, joint design, and weld requirements.
- Lay out, measure, and mark material using tape, squares, levels, protractors, and layout tools; verify cut parts against the print before fit-up.
- Fit and tack components using clamps, jigs, fixtures, and strongbacks to hold dimensional tolerance, root opening, bevel angle, and alignment.
- Plan weld sequence and apply distortion control methods (back-stepping, balanced welding, preheat, restraint) to keep weldments within tolerance.
- Prepare joints by grinding, beveling, and back-gouging using hand grinders, oxy-fuel or plasma torches, and carbon arc gouging.
- Rig and move material and assemblies safely using overhead cranes, hoists, and forklifts (with required site authorization).
Welding
- Perform vertical (3G/3F) and overhead (4G/4F) welds on plate and structural shapes, in addition to flat and horizontal positions, using GMAW, FCAW, and SMAW processes.
- Weld groove and fillet joints, including complete joint penetration welds, to the applicable Welding Procedure Specification (WPS).
- Set up and adjust welding equipment for amperage, voltage, wire feed speed, travel speed, and shielding gas per the WPS.
- Maintain interpass temperature and preheat requirements and record them when required.
- Identify and repair weld discontinuities such as porosity, undercut, lack of fusion, and cracking.
Quality, Documentation, and Safety
- Visually inspect own work against drawing and acceptance criteria; support QA with NDT (VT, MT, PT, UT) and correct rejected welds.
- Maintain material and weld traceability, including heat numbers, welder ID stamping, and travelers, as required by the work order and quality system.
- Follow all safety rules and wear required PPE, including during overhead work, hot work, and work in confined or elevated spaces.
- Keep the work area, tools, and equipment clean, organized, and in good repair; report equipment problems promptly.
- Maintain welder qualification continuity by welding regularly in qualified processes and positions.
- Perform other related duties as assigned.
REQUIRED QUALIFICATIONS
- High school diploma or GED.
- Minimum of 3 years of production or structural welding and fitting experience.
- Demonstrated ability to produce sound vertical-up and overhead welds on plate in at least one of GMAW, FCAW, or SMAW.
- Ability to pass ND Defense's practical weld test in the 3G and 4G positions, including bend test or visual acceptance as specified by the Weld Shop.
- Ability to read blueprints and weld symbols and to fit assemblies to drawing tolerances without direct supervision.
- Working knowledge of shop math, including fractions, decimals, and angle calculation.
- Proficient with grinders, oxy-fuel and plasma cutting, and carbon arc gouging.
- Must be a U.S. Person
PREFERRED QUALIFICATIONS
- Current AWS D1.1 structural welder certification in the 3G and 4G positions.
- Experience welding to military or NAVSEA requirements (for example, MIL-STD-1689 or NAVSEA Technical Publication T9074-AS-GIB-010/271 and S9074-AR-GIB-010/278).
- Aluminum welding experience (GMAW or GTAW) and/or AWS D1.2 certification.
- Pipe welding experience (5G/6G).
- Completion of a welding program through EMCC or another community college, technical school, or registered apprenticeship.
- Overhead crane and forklift operator certification.
- Experience in an AS9100 or ISO 9001 quality environment.
PHYSICAL DEMANDS AND WORK ENVIRONMENT
The physical demands below are representative of those required to perform the essential functions of this job. Reasonable accommodations may be made to enable individuals with disabilities to perform the essential functions.
- Weld and grind in overhead and vertical positions for extended periods, with arms raised and neck extended.
- Stand, kneel, crouch, climb, and work lying down or in awkward positions for much of the shift.
- Lift and carry up to 50 lbs. regularly; move heavier items with cranes, hoists, or team lifts.
- Work in confined spaces and at elevation when required, using fall protection and following confined space procedures.
- Exposure to heat, noise, sparks, spatter, UV radiation, welding fumes, and moving equipment in a manufacturing environment.
- Wear required PPE, including welding helmet, safety glasses, hearing protection, FR clothing, leathers, gloves, and steel-toe boots; respirator use may be required.
- Visual acuity sufficient to inspect welds and read prints, with or without correction.