General Helper

Qualifications:

• Ability to read, write, and follow instructions.
• Read a tape measure.
• Previous experience in painting metal is beneficial.

Must have the knowledge to operate our shop equipment listed below:

• Paint Sprayer
• Forklift
• Oiling Sprayer
• Hoist
• 5-Ton Crane
• Hand Grinders
• Saw
• Drill Press
• Bush-pipe machine
• Trough Straightener

Job Duties:

•

• Perform spray operations to apply standard or special coating to equipment.
• Prepare surfaces, clean, scrap, and grind as necessary to prepare for paint.
• Clean and maintain spray gun and equipment in the paint department daily after every use.
• Be aware of the different stainless steel CEMA finishes and sec finishes.
• Straighten, align, rough grind, and scrap variety of troughs, covers, spouts, etc. to standard.
• Check and straighten troughs to specifications.
• Scrap, grind edges and weldments to eliminate sharp edges and remove weld splatter.
• Use portable hand tools such as grinders, scrappers, portable jacks, hydraulic jacks, furniture clamps, hand drills, etc.
• Understand the procedure used to place part numbers, green tags and job (order) numbers on equipment built and ready for shipment.
• Be responsible for proper paperwork procedures throughout the sheet metal/ paint.
• Be responsible for quality control in the sheet metal clean up department and minimize errors, re- works, and other costly mistakes.
• Help in oiling and stacking of troughs, covers and other items for shipment.
• Be responsible for proper disposal of hazardous waste. (Paint Water, Paint Buckets, Rags with Solvent)
• Check and straighten screws to standard.
• Use drill press and marvel saw when needed.
• Assemble finished conveyors in assembly, when directed by your supervisor.
• Adhere to company Safety Standards, Codes of Safe Practices and Cal/OSHA's Safety Standards.
• Other duties as assigned by your supervisor.

Physical and Initiative Requirements:

• •

• Moderate physical effort, while continuously handling a paint-spraying gun.
• Exposure to varying degrees of noise, paint solvent, fumes, etc.
• Repetitive work. Judgment is required in proper operation of paint gun; ensuring that surfaces are properly covered and evaluating required trough straightening.

This is an entry level and all training will be provided. Hours: 5:45am to 2:15pm Monday thru Friday The pay will start at $17/hr.

Qualifications:

• Ability to read, write, and follow instructions.
• Read a tape measure.
• Previous experience in painting metal is beneficial.

Must have the knowledge to operate our shop equipment listed below:

• Paint Sprayer
• Forklift
• Oiling Sprayer
• Hoist
• 5-Ton Crane
• Hand Grinders
• Saw
• Drill Press
• Bush-pipe machine
• Trough Straightener

Job Duties:

•

• Perform spray operations to apply standard or special coating to equipment.
• Prepare surfaces, clean, scrap, and grind as necessary to prepare for paint.
• Clean and maintain spray gun and equipment in the paint department daily after every use.
• Be aware of the different stainless steel CEMA finishes and sec finishes.
• Straighten, align, rough grind, and scrap variety of troughs, covers, spouts, etc. to standard.
• Check and straighten troughs to specifications.
• Scrap, grind edges and weldments to eliminate sharp edges and remove weld splatter.
• Use portable hand tools such as grinders, scrappers, portable jacks, hydraulic jacks, furniture clamps, hand drills, etc.
• Understand the procedure used to place part numbers, green tags and job (order) numbers on equipment built and ready for shipment.
• Be responsible for proper paperwork procedures throughout the sheet metal/ paint.
• Be responsible for quality control in the sheet metal clean up department and minimize errors, re- works, and other costly mistakes.
• Help in oiling and stacking of troughs, covers and other items for shipment.
• Be responsible for proper disposal of hazardous waste. (Paint Water, Paint Buckets, Rags with Solvent)
• Check and straighten screws to standard.
• Use drill press and marvel saw when needed.
• Assemble finished conveyors in assembly, when directed by your supervisor.
• Adhere to company Safety Standards, Codes of Safe Practices and Cal/OSHA's Safety Standards.
• Other duties as assigned by your supervisor.

Physical and Initiative Requirements:

• •

• Moderate physical effort, while continuously handling a paint-spraying gun.
• Exposure to varying degrees of noise, paint solvent, fumes, etc.
• Repetitive work. Judgment is required in proper operation of paint gun; ensuring that surfaces are properly covered and evaluating required trough straightening.

This is an entry level and all training will be provided. Hours: 5:45am to 2:15pm Monday thru Friday The pay will start at $17/hr.

Compensation / Pay Rate (Up to): $17.00 - $17.00